EN 3065:1996 -
The StandardsDirect Glossary of European / EN Standards
THE EN STANDARDS GLOSSARY
en standards, European standards
Glossary of BC, ISO, and EN Standards

EN 3065:1996 Onwards

Standard No Title of Standard
EN 3065:1996 Installation holes for self-locking, serrated shank nuts. Design standard
EN 307:1999 Heat exchangers. Guidelines for preparing installation, operating and maintenance instructions required to maintain the performance of each type of heat exchanger
EN 308:1997 Heat exchangers. Test procedures for establishing the performance of air to air and flue gases heat recovery devices
EN 3081:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Ferrules welded, with dynamic beam seal end, for repair
EN 3082:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Unions, bulkhead welded, for repair
EN 3083:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Unions, bulkhead, long welded end, for repair
EN 3084:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Unions, welded end threaded for repair
EN 309:2005 Particleboards. Definition and classification
EN 30993-6:1995 Biological evaluation of medical devices. Tests for local effects after implantation
EN 31:1999 Pedestal wash basins. Connecting dimensions
EN 310:1993 Wood-based panels. Determination of modulus of elasticity in bending and of bending strength
EN 31092:1994 Textiles. Determination of physiological properties. Measurement of thermal and water-vapour resistance under steady-state conditions (sweating guarded-hotplate test)
EN 311:2002 Wood-based panels. Surface soundness. Test method
EN 3112:1995 Bolts, normal hexagonal head, threaded to head, in alloy steel, cadmium plated. Classification: 900 MPa (at ambient temperature)/235$0DC
EN 312:2003 Particleboards. Specifications
EN 31253:1996 Lasers and laser-related equipment. Laser device. Mechanical interfaces
EN 313-1:1996 Plywood. Classification and terminology. Plywood. Classification and terminology. Classification
EN 313-2:2000 Plywood. Classification and terminology. Terminology
EN 3135:1996 Rivets, solid, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series
EN 3136:1996 Rivets, solid, universal head, in corrosion resisting steel FE-PA92HT, passivated, inch based series
EN 3138:2001 Aerospace series. Rivets, solid 100$0D countersunk normal head with dome, in corrosion resisting steel FE-PA2601, passivated, inch based series
EN 3139:2001 Aerospace series. Rivets, solid, 100$0D countersunk normal head, in corrosion resisting steel FE-PA11, passivated, inch based series
EN 3140:2001 Aerospace series. Rivets, solid, 100$0D countersunk normal head, in corrosion resisting steel FE-PA2601, passivated, inch based series
EN 314-1:1993 Plywood. Bonding quality. Test methods
EN 3141:1996 Rivets, solid, universal head, in heat resisting nickel base alloy NI-P11, cadmium plated, inch based series
EN 314-2:1993 Plywood. Bonding quality. Requirements
EN 3142:1996 Rivets, solid, universal head, in heat resisting nickel base alloy NI-P11, inch based series
EN 31427:1994 Determination of silver in silver jewellery alloys. Volumetric (potentiometric) method using potassium bromide
EN 3145:2002 Round bars, hot rolled in steel. Normal tolerances. Diameter 6 mm $3L D $3L 250 mm. Dimensions
EN 3146:2001 Aerospace series. Round bars, hot rolled in steel. Close tolerances. Diameter 6mm $3L D $3L 250mm. Dimensions
EN 3149:1997 Shank nuts. Installation holes, 60$0D swage, flanges. Design standard
EN 315:2000 Plywood. Tolerances for dimensions
EN 3150:1995 Pins, shoulder, headless, in heat resisting nickel base alloy NI-P100HT (Inconel 718)
EN 3151:1995 Dowels, plain, in heat resisting nickel base alloy NI-P100HT (Inconel 718)
EN 3152:2004 Aerospace series. Nuts, self-locking, MJ threads, in heat resisting steel FE-PA2601 (A286), silver plated or uncoated. Classification: 1100 MPa (at ambient temperature)/425$0DC.
EN 316:1999 Wood fibreboards. Definition, classification and symbols
EN 317:1993 Particleboards and fibreboards. Determination of swelling in thickness after immersion in water
EN 318:2002 Wood based panels. Determination of dimensional changes associated with changes in relative humidity
EN 319:1993 Particleboards and fibreboards. Determination of tensile strength perpendicular to the plane of the board
EN 3196:1994 Nuts, hexagonal, self-locking, in heat resisting steel FE-PA92HT (A286), silver plated. Classification: 1100 MPa (at ambient temperature)/425$0DC
EN 32:1999 Wall-hung wash basins. Connecting dimensions
EN 320:1993 Fibreboards. Determination of resistance to axial withdrawal of screws
EN 3202:1995 Holes and traps for T-head bolts. Design standard
EN 3207:1998 Rubber compounds. Technical specification
EN 321:2002 Wood-based panels. Determination of moisture resistance under cyclic test conditions
EN 3212:1995 Paints and varnishes. Corrosion test by alternate immersion in a buffered sodium chloride solution
EN 322:1993 Wood-based panels. Determination of moisture content
EN 323:1993 Wood-based panels. Determination of density
EN 3230:2001 Aerospace series. Nuts, hexagon, slotted/castellated, reduced height, normal across flats, in steel, cadmium plated. Classificaiton: 900 MPa (at ambient temperature)/235$0DC
EN 3236:1998 Inserts, thin wall, self-locking, short, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated internal thread
EN 3237:1998 Inserts, thin wall, self-locking, long, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated internal thread
EN 3239:1996 Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated thread. Classification: 1210 MPa (at ambient temperature)/730$0DC
EN 324-1:1993 Wood-based panels. Determination of dimensions of boards. Determination of thickness, width and length
EN 324-2:1993 Wood-based panels. Determination of dimensions of boards. Determination of squareness and edge straightness
EN 3243:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Ferrule, welded, with dynamic beam seal end
EN 3244:2001 Aerospace Series. Pipe coupling 8$0D30' in titanium alloy. Unions, double ended
EN 3245:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Unions, reducer
EN 3246:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Unions, bulkhead
EN 3247:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Unions, bulkhead welded end
EN 3248:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Adaptors, reduced pipe end, with lockring
EN 325:1993 Wood-based panels. Determination of dimensions of test pieces
EN 326-1:1994 Wood-based panels. Sampling, cutting and inspection. Sampling and cutting of test pieces and expression of test results
EN 326-2:2000 Wood-based panels. Sampling, cutting and inspection. Quality control in the factory
EN 326-3:2003 Wood-based panels. Sampling, cutting and inspection. Inspection of an isolated lot of panels
EN 3264:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Thrust wire nut
EN 3266:2001 Aerospace series. Pipe coupling in titanium alloy. Bulkhead nut
EN 3267:2001 Aerospace series. Washers, bulkhead in titanium alloy
EN 3268:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Pressure plug
EN 3269:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Ferrules, blind, with dynamic beam seal end
EN 327:2000 Heat exchangers. Forced convection air cooled refrigerant condensers. Test procedure for establishing performance
EN 3270:2001 Aerospace series. Pipe coupling 8$0D30' in titanium alloy. Blanking plug with lockring
EN 3272:2001 Aerospace series. Pipe coupling 8$0D30'. Dynamic beam seal end for ferrule, welded. Geometric configuration
EN 3273:2001 Aerospace series. Pipe coupling 8$0D30'. Dynamic beam seal end for elbows, tees and crosses. Geometric configuration
EN 3274:2001 Aerospace series. Pipe coupling 8$0D30'. Thread. Geometric configurations
EN 3275:2002 Aerospace series. Pipe coupling 8$0D30' up to 28000 kPa. Dynamic beam seal. Metric series. Technical specification
EN 328:1999 Heat exchangers. Test procedures for establishing the performance of forced convection unit air coolers for refrigeration
EN 3280:1994 Bearings, airframe rolling, rigid or self-aligning. Technical specification
EN 3281:1994 Bearings, airframe rolling. Rigid single row ball bearings in steel. Diameter series 8 and 9. Dimensions and loads
EN 3282:1994 Bearings, airframe rolling. Rigid single row ball bearings in steel, cadmium plated. Diameter series 8 and 9. Dimensions and loads
EN 3283:1994 Bearings, airframe rolling. Rigid single row ball bearings in corrosion resisting steel. Diameter series 8 and 9. Dimensions and loads
EN 3284:1994 Bearings, airframe rolling. Rigid single row ball bearings in steel. Diameter series 0 and 2. Normal clearance category. Dimensions and loads
EN 3285:1994 Bearings; airframe rolling. Rigid single row ball bearings in steel, cadmium plated. Diameter series 0 and 2. Normal clearance category. Dimensions and loads
EN 3286:1994 Bearings, airframe rolling. Rigid single row ball bearings in corrosion resisting steel. Diameter series 0 and 2. Normal clearance category. Dimensions and loads
EN 3287:1994 Bearings, airframe rolling. Double row self-aligning ball bearings in steel. Diameter series 2. Dimensions and loads
EN 3288:1994 Bearings, airframe rolling. Double row self-aligning ball bearings in steel, cadmium plated. Diameter series 2. Dimensions and loads
EN 3289:1994 Bearings, airframe rolling. Double row self-aligning ball bearings in corrosion resisting steel. Diameter series 2. Dimensions and loads
EN 3290:1994 Bearings, airframe rolling. Single row self-aligning roller bearings in steel. Diameter series 3 and 4. Dimensions and loads
EN 3291:1994 Bearings, airframe rolling. Single row self-aligning roller bearings in steel, cadmium plated. Diameter series 3 and 4. Dimensions and loads
EN 3292:1994 Bearings, airframe rolling. Single row self-aligning roller bearings in corrosion resisting steel. Diameter series 3 and 4. Dimensions and loads
EN 3297:1998 Inserts, thin wall, self-locking, MJ threads, in heat resisting nickel base alloy NI-P100HT (Inconel 718). Technical specification
EN 3298:1998 Inserts, thin wall, self-locking. Installation and removal procedure
EN 3-3:1996 Portable fire extinguishers. Construction, resistance to pressure, mechanical tests
EN 33:2003 Pedestal W.C. pans with close-coupled flushing cistern. Connecting dimensions
EN 330:1993 Wood preservatives. Field test method for determining the relative protective effectiveness of a wood preservative for use under a coating and exposed out-of-ground contact. L-joint method
EN 3303:1997 Screws, cap head, hexagon socket, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated. Classification: 1100 MPa (at ambient temperature)/235$0DC
EN 3304:1997 Screws, 100$0D countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS$d2 lubricated.
EN 3305:1997 Screws, 100$0D countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated.
EN 3306:1996 Screws, 100$0D countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS$d2 lubricated. Classification. 1100 MPa (at ambient temperature)
EN 3307:1997 Screws, pan head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS$d2 lubricated. Classification: 1100 MPa (at ambient temperature)/315$0DC
EN 3308:1996 Screws, normal hexagonal head, threaded to head, in titanium alloy, anodized, MoS$d2 lubricated. Classification. 1100 MPa (at ambient temperature) /315$0DC
EN 331:1998 Manually operated ball valves and closed bottom taper plug valves for gas installations in buildings
EN 334:1999 Gas pressure regulators for inlet pressures up to 100 bar
EN 335-1:1992 Hazard classes of wood and wood-based products against biological attack. Classification of hazard classes
EN 335-2:1992 Hazard classes of wood and wood-based products against biological attack. Guide to the application of hazard classes to solid wood
EN 335-3:1996 Hazard classes of wood and wood-based products against biological attack. Application to wood-based panels
EN 336:2003 Structural timber. Sizes, permitted deviations
EN 3377:1996 Nuts, hexagonal, self-locking, in heat resisting steel FE-PA92HT (A286). Classification: 1100 MPa (at ambient temperature)/425$0DC
EN 3379:1996 Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), for increased height nuts.
EN 338:2003 Structural timber. Strength classes
EN 3380:1996 Rings, retaining. Technical specification
EN 3381:1997 Screws, 100$0D countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium, anodized, MoS$d2 lubricated.
EN 340:2003 Protective clothing. General requirements
EN 341:1993 Personal protective equipment against falls from a height. Descender devices
EN 342:2004 Protective clothing. Ensembles and garments for protection against cold
EN 343:2003 Protective clothing. Protection against rain





To receive a price quote for any EN standard, please review our partners on the right


Return To The EN Standards Glossary Index






HOW TO OBTAIN STANDARDS 
To receive a direct quote for any EN standard, please review our partners below.

OTHER INFORMATION





Copyright StandardsDirect. European Standards.